Call

 

We've come across this great article involving How to Install a Bathtub directly below on the net and believe it made good sense to share it with you on my blog.

Mounting a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough job. If the old tub is readily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old tub and also position the new bathtub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old tub and set in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This article will certainly help you set up a brand-new bath tub in your restroom if you have already bought a brand-new tub as well as do not require to change the plan of your previous supply of water pipes.
Your tools as well as product list must consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome because of the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Safeguard the tap in position with the maker given backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former type must be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Setting up the Bathtub

Utilizing both wooden boards under its feet, place the bath tub in the called for position. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bathtub till the level reviews level.
To mount faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the water and examine all joints and brand-new pipework for leaks as well as tighten them if required. Load the bath tub and additionally examine the overflow outlet as well as the normal outlet for leakages.
Lastly, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bathtub has actually been made use of at the very least when as this will settle it into its final setting.

 

 

Getting ready for the Installment

First of all, the supporting structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final position.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly load the tub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently available on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I found that piece about Tools You Need to Install a New Bathtub when doing a lookup on the internet. Do you know about another person who is occupied with the subject? Feel free to promote it. Thank you so much for taking the time to read it.

Just a call away!